Відео

Exactly what I needed. Generator up and running normal again. Super easy fix.

Pull fridge out and vacuum floor of broken glass (almost always some there - in my house anyway :-). Air compressor with air blow gun attachment, shop vac outlet port, computer cleaner compressed air can, leaf blower. Vacuum/ or garage vacuum: Attach old flexible cpap hose to the end to slip around corners. Online stores sell flexible hose attachments too. Search vacuum cleaner flexible hose, or dryer vent cleaning hose. Look for a hose that won't crease when going around the 90 degree corner.

Looking to buy an air compressor, not sure how they work. Do they need to be outside like a generator, and just use a long hose attached? What size air compressor will handle this job? Thanks!

Thanks that's was great advice, AJ

how can u tell it gets hot? which parts get hot

What kind of air compressor should I use and where do I buy one?

Yeah do not do this. It’ll void your warranty and you will get hurt. Do NOT DO THIS

Thank you, my Generator runs great thanks to your video.

I have Honda EU7000 I have power on 110v plug but not 220v plug can you help what is the issue with 220v plug

Have you tried this with Milwaukee batteries

I came here looking for ideas on how to access the center section of the coils beneath my fridge, as I was only able to manuver the brush I bought into the forward-most section of the coil array (my coils look almost exactly like the ones in your video) and vacuuming only cleared the very front bit of the coils. I would never have occurred to me to use an air compressor to blow the lint free, and a box fan with improvised filter to catch it all. This is a great idea, and it worked perfectly for me. Thank you! Thank you also for advising to unplug the fridge to preclude one having to "round up free range dust bunnies" 😂👌

Thank you!!! I have had a problem with my generator that it will only run with the choke slightly closed. I had cleaned the carburetor 2 times and checked the needle valve, ect. The key was that secondary black screw trick where the tube was clogged with a piece of dirt. It runs perfect now!!!

how about a video on the Shark vacuum 3-4 v batteries?😊

hey !@! u didn't tell me 2 keep that charger UNPLUGED ! 😢😢😢😢😢😢😢😮

Excellent video! I had to run on partial choke. Would still run fully open, but far from smoothly. Duromax XP4400E. I knew it wasn't bad gas, so I did the carb things you suggested. The jet and tube holes didn't seem clogged at all, but I ran the tiny wire through them anyway. I tried the same on the teeny tiny jet, but it seemed the wire was slightly too big to go all the way through, so I sprayed some brake cleaner in it. Wire still wouldn't go through so I put it back together not expecting the issue to be solved, but it was. Runs perfectly now. Thanks!

U basically built a new one heeh

Regarding the overheating - the manual tells to place on smooth ground, so I think a carpet will not allow enough airflow underneath to prevent overheating

Mines still flashing fml

Thanks for such a lucid explanation of a complex topic. cheers

Then why would Honda but a lug for a ground rod on my 6500 generator.

Every hurricane season I always start my generators and make sure they are running like they are suppose to. This year I went to start it and it will only run with the choke on. Hopefully this resolves my issue. I always turn my fuel off and allow the generator to run until it runs out of fuel just so there is nothing left so idk how it would get clogged. I also don't leave any gas in the tank and drain it all out into a gas can prior to storing it.

Totally wrong on tilting the can over under pressure and opening it up

This! This was exactly my issue. My piston was firing but not completely retracting back into the gun to fire the next nail. Hence the “thunk” without the nail. This fixed it up perfectly. Thank you!

My neighborhood has a bulk trash day, and I found one of these safes in brand new condition in the trash pile so I'm trying to figure out how to open it. Depending on the size I think it might be a good safe to put my primers and gunpowder for reloading and mount it to my reloading table

Bruh, genius!

How in the heck do you adjust if you’re using your generator to run your house in a power outage?

What about a home emergency generator connected to a main panel with interlock (i.e. no transfer switch)? I gather the generator should be floating neutral since the house has it's own nuetral to ground connection. But, in this case, with a generator with a floating-nuetral, what happens when there is a fault in the generator? Seems like your damned if you and damned if you don't. By the way, this is THE clearest video on the subject. I've listened to 10 today and didn't understand a god-damn thing they said. Thanks for your efforts.

Early stage of heroes in mouth

Why does champion say to soak the foam air filter in clean oil?

Does it matter if my generator is brand new? Mine is doing this but this is the first it's had fuel and has ever been started.

I wonder if the vinegar for cleaning with higher acid would do better.

Thank you. Great exact procedures.

That's why I like the older stoves in the 70s lighting took my parents' gas oven and it had to be repaired. I have a gas stove from the 50s, and the oven works even when the power is out.

As of 2024, my Ryobi 18V mower battery (not charging) has no screws on the underside. I wonder if they redesigned due to videos like this?

I've got a 19 year old water heater (12 year lifespan guarantee) and the rod has never been removed. I'm wondering if it's too late to bother with it and should just buy a new water heater??

Thank you so much you saved my day of riding lol

Saved another battery from the dumpsters! This trick work very well, the battery worked after reaching 15v

DO NOT USE WD40. Use " 3 in 1 type oil" / sewing machine oil etc . WD40 wont last at all as it will evaporate off leaving no lube at all

That old battery charger is very useful for desulfation repair.

Mine machine starts, runs for about 4 seconds and then stalls. You don't have to wait to start it again. You can start it a hundred times in a row, and it will stall after four seconds. Also, you can keep it running by pressing the primer bulb every few seconds. So, what's the differential diagnosis for a machine that will start every time (with priming), but then stalls.

Alligator clips can be worth it if you do this enough

Wouldn't tuning your generator while it's under load potentially fry those electronics if the hz is above 62? Seems like the backwards way of doing this, or am I missing something?

Irreversible damage. No. It can always be repaired.

Thank you. I have this exact setup, but I don't own an air compressor. Is there any way to remove the coils for cleaning or is that just too much?

0:34 seconds in and I found my solution. The circuit breaker was off. Flipped it in ON position and it worked!

This is a feature that makes a battery charger completely fucking useless.

Great video, was so informative, thanks.

What would you suggest as an alternative?

Thank you I just jumped started a Ryobi 18v 4ah battery

Can you not just have one good battery and one dead run one wire to positive and run wire to native without opening batteries lot more simpler???